SANITARY AUTOMATIC BALL VALVES:
FEATURES:
- All stainless steel and Mica-filled Teflon construction Type 316 product contact parts.
- Full Mica-filled Teflon seals eliminate voids in which product may accumulate.
- Valve port fully nominal diameter.
- Unobstructed product flow.
- Type outlets: *Tri-Clamp connections. **I-line and Sanitary Acme Threads, ASA flanges, 105 or 300 PSIG rating.
- Handle doubles as a wrench to tighten packing nut.
- Easily disassembles in less than thirty seconds.
- Meets 3A requirements.
|
- Approved by USDA.
- Each valve is tested before shipment.
- Maximum working pressure is 300 PSIG.
- Maximum working temperature is 450F.
- Face-to-face dimension is interchangeable with sanitary plug valves.
- In-line adjustment to compensate for seal wear.
- Mounting flange is easily welded to any style tank bottom: hemispheric, dished, flat, cone, etc.***
- Flush with bottom of vessel.***
|
| *Registered trademark Ladish Co. **Registered trademark of Cherry Burrell Co. ***Flush type Only. |
|
|
 |
SANITARY AIR ACTUATED FLUSH-TYPE FLUID-FLOW BALL VALVES
| |
Fluid Transfer's air actuated flush-type ball valves are precision made of 316 stainless steel welded parts with type 316-L stainless steel mounting flange.
The corrosion-resistant, sanitary design of Fluid-Flow ball valves makes them ideal for use in the food, cosmetic, pharmaceutical, beverage, and chemical industries.
Where flush-type ball valves are not easily accessible for manual operation, they can be equipped with air actuators for remote actuation.
The actuators can be triggered through a switch or control panel.
Air actuated Fluid-Flow flush-type ball valves lend themselves to C.I.P. (clean in place) systems.
Vane type, rack and pinion air-to-air or spring-return actuators are available.
The vane actuator housing is constructed of die-cast aluminum and is externally coated with baked epoxy.
The rack and pinion actuator is standard with a precision extruded hard-anodized aluminum body and pistons for long life and corrosion resistance.
Stainless steel is also available.
The temperature range for air actuators on Fluid-Flow ball valves is -40F to +180F.
Completely sealed and weather proofed, each unit is inspected and factory tested.
|
SANITARY AIR ACTUATED IN-LINE, FLUID-FLOW BALL VALVES
| |
Fluid-Transfer's two-way and three-way diverter air actuated in-line Fluid-Flow ball valves are designed for rigid corrosion-resistant, high sanitary applications in the food, cosmetic, pharmaceutical, beverage and chemical industries.
Standard fully encapsulating Mica-Filled Teflon seals provide the maximum reduction in product entrapment while full flow ports, also standard, eliminate product flow restrictions.
The 90 degree vane-type air-to-air actuator allows for on-off operation when connected to Fluid-Flow two-way in-line ball valves.
Cycle time is approximately 1 second for both types of actuators, allowing for positive shut off in a short period of time.
Rack and pinion actuators are offered in air-to-air and spring return designs.
|
THREE-WAY IN-LINE DIVERTER VALVES
| |
Fluid Transfer's Fluid Flow three-way in-line diverter ball valves provide an efficient means of simplifying multiple tank filling and draining operations.
When connected to three-way in-line diverter valves, the 90 degree rack and pinion actuators offer two directions of flow, straight through or right angle flow.
When equipped with a 180 degree rack and pinion actuator, the valve has a two directional flow as well as off position.
|
SUPERNOVA S-SERIES RACK & PINION ACTUATORS
| |
Benefits - XL Series
The Automax Directional valve mounts directly to SuperNova series actuators which eliminates the cost of tubing and fittings. The valves are available for double acting and spring return actuators with Nema 4, 4X, 7 & 9, or intrinsically-safe and low power solenoid operators. These valves have been tested and proven reliable for over 1 million cycles.
Design Benefits
- Integral travel stops in both directions with 10 degrees of overtravel to assure precise adjustments of both the open and closed positions.
- Full length gear engagement between piston rack & electroless nickel plated pinion.
- Flats on pinion drive shaft accommodate wrench overrides and accessories.
- Field reversible action simply by rotating pistons 180 degrees.
- Precision die cast pistons with large cylinder bearings increase efficiency and cycle file.
- Valve, accessory and NAMUR control mounting pads.
- Corrosion resistant hard anodized aluminum housings with stainless steel fasteners.
- One compact design for double acting and spring return is easily field-convertible by installing and removing springs.
- Broad size range offers optimum actuator sizing for each valve requirement.
|
|
 |
CONTROLS & ACCESSORIES: Ultra Switches
| |
Benefits XL Series:
Nema 4, 4X, 7 & 9
Class 1, Groups C & D, Divisions 1 & 2
Class II, Groups E, F & G, Divisions 1 & 2
Porting Compartments to Nema Specifications
Terminal Strip Contacts: 2 open contacts provided SPST, SPDT, and DPDT mechanical and proximity switches with multipoint terminal strip.
Integral potting of leads and two 3/4" conduit entries
"Quick Set" cams and captive cover bolts
Options:
- Analog resistive and current outputs
- "Pharos" or flat cover
- Universal mounting adaption
- Integrated solenoid valves
|
|
 |
CONTROLS & ACCESSORIES: Positioners
| |
Benefits:
Available in Aluminum (Apex Series) & Non-Metallic Housings (H-Series)
Outstanding performance and reliability
Simple mechanical zero and span adjustments
Pressure and temperature compensated with integral filter for the E-P model
Standard hi and max flow spool valves with low bleed
RFI protected, corrosion resistant, weatherproof housing
Options:
- Integral limit switches and/or analog outputs
- "Pharos" or "flat lens" position indicators
- Universal mounting adaption
|
|
 |
VANE TYPE ACTUATORS
| |
Features:
- Simple Design - only one moving part, the vane (paddle) is cast integral to the shaft.
- Direct Transmission - provides excellent repeatability.
- External Stroke Adjustment - allow a wide range of vane travel.
- Constant Torque Output.
- Die-Cast Aluminum Housing.
- Modular Construction.
|
|
 |
OPTIONS AND ACCESSORIES
| |
Features:
- UltraSwitch with and without Pharos indicator
- Nema 4, 4X, 7 & 9
- 4 Proximity switches SPDT
- Standard output signal: 4-20 made, 2 wire
- Power requirements: 18 to 30 VDC
- Output loading: 0 to 750 ohms at 24 VDC
- Solenoids
- Speed Controls
- Filter Regulator
- Manual Override
- Mounting Hardware
- Stainless Steel Actuators (for corrosive environments)
- Special Control Circuits
- Electronic Actuators
|
|
In today's competitive marketplace and economic environment, it has become necessary for the process manufacturer to develop innovative process designs in producing their product. Very often, standard, off-the-shelf items do not conveniently fit the needs of these pioneering companies.
Fluid Transfer understands this situation and designs and manufactures special application ball valves that fit into an individual company's process system needs. A staff of eminently qualified design engineers is ready to modify the Lee standard ball valves to your specifications. Each specially designed valve will be manufactured with the same care and precision that Lee craftsmen have exhibited for over 75 years.
|
|
 |
|
